{
  "id": "invisible-door-hinges",
  "sku": "invisible-door-hinges",
  "title": "Invisible Concealed Door Hinges (2 Pairs, 180 Degree)",
  "slug": "invisible-door-hinges",
  "price": 40.99,
  "currency": "GBP",
  "availability": "in_stock",
  "category": "door-hinges",
  "category_label": "Door Hinges",
  "tags": [],
  "colors": [],
  "materials": [],
  "dimensions": null,
  "weight": "246 g",
  "images": [
    "https://hingecompany.co.uk/dropship-images/door-hinges/invisible-door-hinges/main-invisible-door-hinges.jpg",
    "https://hingecompany.co.uk/dropship-images/door-hinges/invisible-door-hinges/invisible-door-hinges-2.jpg"
  ],
  "description_short": "Polished stainless steel construction, eight mounting holes per hinge, a 22 pound load rating and a full 180 degree swing for doors that open wide and sit flush.",
  "description": "The problem with hinges you can see\n\nYou can spend a weekend building a cabinet, sand it smooth, get the grain matching across the doors, apply three coats of oil, and then screw on a pair of shiny butt hinges that drag your eye straight to them. Hardware has a way of doing that. The door face is the thing people look at, and anything breaking that face reads as a join rather than a surface.\n\nInvisible hinges fix the problem by getting out of the way. They are cut into the edge of the door and the matching edge of the frame, so the whole mechanism folds up inside the timber. Close the door and there is nothing to see but a thin shadow line. Open it and the hinge unfolds out of its recess.\n\nThis set is a pair of stainless steel hinges, 44mm long by 44mm wide, with a polished silver finish. Each hinge carries up to 22 pounds and opens a full 180 degrees. They suit cabinet doors, lift lids, boxes, display cases and custom joinery where the hardware is supposed to be felt rather than seen.\n\nHow a concealed hinge actually works\n\nA butt hinge is two flat plates joined by a pin. One plate screws to the door edge, the other to the frame, and the knuckle sits in the gap between them. Simple, strong, visible.\n\nA concealed hinge of this type uses a linked mechanism instead. When the door is shut, the links fold flat into two small recesses, one in the door and one in the frame. When the door opens, the links unfold and swing the door clear of the frame. Because the pivot moves as the door opens, the door can swing well past 90 degrees without the edge fouling the carcass.\n\nThat is why the 180 degree figure matters. A lot of hidden hinges stop at 90 or 110 degrees, which is fine for a lid but annoying on a cupboard you want to reach into properly. At 180 degrees the door lies back flat against the side of the cabinet and stays out of your way.\n\nThe eight mounting holes per hinge are there for a reason too. On a surface mounted hinge the leaf spreads the load across a wide area of timber. A concealed hinge has a smaller footprint, so the screws do more work. Eight fixing points share that load and reduce the chance of one screw pulling out over time.\n\nWho these suit\n\nThink about weight first. At 22 pounds per hinge, a pair carries a fair amount for a cabinet door but is not meant for a full size internal house door. Passage doors are much heavier and need an architectural concealed hinge rated for that duty. If your project is a wardrobe front, a display cabinet, a kitchen cupboard door, a chest lid or a keepsake box, you are in the right territory.\n\nThickness matters next. Because the hinge buries itself in the timber, both the door edge and the frame edge need enough material to take the recess and still have solid wood left either side. Hollow core panels and thin plywood are not suitable. Solid timber gives the best screw hold, MDF works if the panel is thick enough and you pilot drill carefully, and chipboard is the weakest option because the mortise removes so much of the core.\n\nOne more thing to consider is adjustment. European cup hinges have three adjustment screws that let you nudge a door up, across and in or out after it is hung. Mortise hinges do not. All the alignment comes from how accurately you mark and cut. That is not a problem if you take your time, but it does mean this is a measure twice job.\n\nFitting them without the headaches\n\nThe order of work is what makes this easy or hard. Hang the door in the opening first and pack it with shims so the gaps are even all round. That gives you a reference to mark against, rather than trying to calculate positions on a bench.\n\nWith the door held in place, decide where the hinges go, usually a consistent distance down from the top and up from the bottom. Hold a hinge in position and scribe around it with a marking knife. A knife line is far more accurate than a pencil line, and the cut edge gives your chisel something to register against.\n\nSet a marking gauge to the thickness of the hinge leaf and run it along the inside of the scribed area to mark the depth. That depth line is the single most important mark in the whole job. Cut too shallow and the hinge stands proud, so the door will not close. Cut too deep and the door binds against the frame.\n\nPare the recess with a sharp chisel, working across the grain in shallow passes rather than trying to lift out a thick chip. A series of light chisel cuts across the length of the recess breaks the waste into manageable pieces. A router with a straight bit and a simple template is quicker if you have several doors to do.\n\nTest fit before drilling. The hinge should sit flush with the surface with no rocking. Then pilot drill each screw hole, ideally with a self centring bit so the screws pull the hinge tight rather than dragging it sideways. Fit the hinges to the door first, offer the door back into the opening, mark the frame positions, and repeat the process on the frame.\n\nScrew everything down, check the swing, and adjust the recess depth with a few chisel strokes if the door binds anywhere. Done properly the door closes with a quiet click and sits dead level with the frame.\n\nLooking after them\n\nConcealed hinges need very little attention, but a bit of care keeps them smooth. Dust is the main enemy, since it settles in the folding links and gradually makes the action gritty. A wipe with a soft dry cloth every so often is enough.\n\nIn damp rooms like bathrooms and laundries, dry the hinge after cleaning so moisture does not sit in the knuckle. Stainless steel resists corrosion well, but no finish likes standing water. Skip abrasive pads, scouring powders and bleach based sprays, all of which will dull a polished surface.\n\nRetighten the mounting screws a couple of times a year on doors that get opened constantly. A screw that has worked slightly loose is easy to fix early and a nuisance to fix once the hole has worn. A trace of light machine oil on the pivot will quiet a squeak without attracting grime.\n\nIf the door is being painted, fit the hinges afterwards or mask them properly. Paint building up in the mechanism is the most common reason a concealed hinge stops closing flush.\n\nChoosing between hinge types\n\nQuick comparison if you are still deciding. Butt hinges are cheap, strong and easy to fit, but always visible. Cup hinges are adjustable and fast on a kitchen full of doors, but they take up room inside the carcass and show their arms when the door opens. Piano hinges are great for long lids and terrible for looks.\n\nConcealed mortise hinges, like these, win on appearance and lose on adjustability. They are the right call when the finished look matters most, on a feature cabinet, a fine box, a built in unit where you want the joinery to read as one continuous surface.\n\nThe short version\n\nThese are stainless steel invisible hinges, 44mm square, polished silver, two in the set. Each one takes up to 22 pounds and opens a full 180 degrees, with eight mounting holes to spread the load.\n\nThey work best on cabinet doors, lids, boxes and joinery built from solid timber thick enough to take the mortise. They are not for heavy passage doors, and they are not adjustable once fitted, so accurate marking is the whole job.\n\nTake your time with the recess depth, use every screw hole, and you will end up with a door that opens wide, closes flush and shows no hardware at all.",
  "llm_summary": "Invisible concealed door hinges from Auto-plaza, supplied as a 2 count set. Each hinge is stainless steel with a polished silver finish and measures 44mm long by 44mm wide, with 8 mounting holes and a door mount fixing. They open a full 180 degrees and carry a maximum weight capacity of 22 pounds per hinge. Total item weight is 246 g. The hinges mortise into the door edge and frame so no hardware is visible when the door is closed, which suits cabinet doors, boxes, display cases and custom joinery. UPC 778299509404, model 4e41da5a-1bc3-4d23-845a-0cfd0fc59de5, condition new. Colour is silver. Country of origin and overall thickness are not listed by the maker.",
  "returnable": true,
  "return_policy": "Voluntary 14-day change-of-mind returns in original condition, buyer pays return postage; the Consumer Rights Act 2015 for faulty goods. Return postage on faulty goods is ours.",
  "shipping_profile": "standard",
  "warranty": null,
  "brand": "Hinge Company",
  "gtin": null,
  "mpn": null,
  "condition": "new",
  "url": "https://hingecompany.co.uk/invisible-door-hinges/",
  "canonical_url": "https://hingecompany.co.uk/invisible-door-hinges/",
  "json_url": "https://hingecompany.co.uk/api/products/invisible-door-hinges.json",
  "updated_at": "2026-10-19"
}